+ Reply to Thread
Page 5 of 13 FirstFirst 1 5 13 LastLast
Results 81 to 100 of 248

Thread: Technological advances that will directly affect you in the next 2 years

  1. Link to Post #81
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Quote Vasalgel (reversible, long term male birth control) preclinical studies making great progress!
    The last few months have been incredibly active preparing for the next phases of the baboon preclinical studies. The short version: We think we're back on track, and we could use your help!

    Three baboon subjects from the original study have now had Vasalgel for 6 months. (Want to know why we had to do a second round? Read all about it here.) To make sure that it is still working prior to reversal, we decided to give all of the males an opportunity to mate with females to ensure that no pregnancies occur. Each of the three male baboons was moved into enclosures with 10-15 females (yes, that's 10-15 each!) a month ago. And the good news? So far no pregnancies. But they will remain with the females for at least a few more weeks just to be sure. We are planning to flush out the Vasalgel - to attempt to reverse it, like was done in the rabbit study - early next month. Then we will check to see whether sperm start to flow once again.

    The newer baboon study has also just started. After a health check, five males got Vasalgel last week. Three more are planned. The baboons will rest for a bit while we monitor them closely, then will be moved to breeding enclosures with fertile females. Half of the baboons will be able to mate with females for three months, and half of them will be with females for six months. After this, they will all undergo reversal and additional testing.

    By the time the year ends, we will have a lot more information on the efficacy of Vasalgel - and, if all goes well, will be planning for clinical trials with humans to start next year.
    http://myemail.constantcontact.com/V...id=Wt_qWj4Sr-M
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  2. The Following 3 Users Say Thank You to TargeT For This Post:

    Cara (4th December 2015), meeradas (15th October 2014), Star Tsar (5th November 2014)

  3. Link to Post #82
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Quote Nanotechnology aids in cooling electrons without external sources
    A team of researchers has discovered a way to cool electrons to -228 °C without external means and at room temperature, an advancement that could enable electronic devices to function with very little energy.


    A chip, which contains nanoscale structures that enable electron cooling at room temperature, is pictured.

    The process involves passing electrons through a quantum well to cool them and keep them from heating.

    The team details its research in “Energy-filtered cold electron transport at room temperature,” which is published in Nature Communications on Wednesday, Sept. 10.

    “We are the first to effectively cool electrons at room temperature. Researchers have done electron cooling before, but only when the entire device is immersed into an extremely cold cooling bath,” said Seong Jin Koh, an associate professor at UT Arlington in the Materials Science & Engineering Department, who has led the research. “Obtaining cold electrons at room temperature has enormous technical benefits. For example, the requirement of using liquid helium or liquid nitrogen for cooling electrons in various electron systems can be lifted.”

    Electrons are thermally excited even at room temperature, which is a natural phenomenon. If that electron excitation could be suppressed, then the temperature of those electrons could be effectively lowered without external cooling, Koh said.

    The team used a nanoscale structure – which consists of a sequential array of a source electrode, a quantum well, a tunneling barrier, a quantum dot, another tunneling barrier, and a drain electrode – to suppress electron excitation and to make electrons cold.

    Cold electrons promise a new type of transistor that can operate at extremely low-energy consumption. “Implementing our findings to fabricating energy-efficient transistors is currently under way,” Koh added.

    Khosrow Behbehani, dean of the UT Arlington College of Engineering, said this research is representative of the University’s role in fostering innovations that benefit the society, such as creating energy-efficient green technologies for current and future generations.

    “Dr. Koh and his research team are developing real-world solutions to a critical global challenge of utilizing the energy efficiently and developing energy-efficient electronic technology that will benefit us all every day,” Behbehani said. “We applaud Dr. Koh for the results of this research and look forward to future innovations he will lead.”

    Usha Varshney, program director in the National Science Foundation’s Directorate for Engineering, which funded the research, said the research findings could be vast.

    When implemented in transistors, these research findings could potentially reduce energy consumption of electronic devices by more than 10 times compared to the present technology,” Varshney said. “Personal electronic devices such as smart phones, iPads, etc., can last much longer before recharging.”
    http://www.uta.edu/news/releases/201...ing-nature.php
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  4. The Following 7 Users Say Thank You to TargeT For This Post:

    animovado (11th September 2014), Cara (4th December 2015), Hervé (11th September 2014), meeradas (15th October 2014), seko (12th October 2014), sigma6 (27th October 2014), Star Tsar (5th November 2014)

  5. Link to Post #83
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    First shot fired!


    Software sort of counts as technology right? This will be momentous.

    Quote Overstock.com Becomes First Major Retailer to Accept Bitcoin Worldwide

    Overstock.com was the first major online retailer to embrace bitcoin, accepting payments in the digital currency here in the U.S. beginning in early January. And now, it’s the first to accommodate bitcoin across the globe.

    Early this morning, the Salt Lake City-based company started accepting bitcoin payments in all foreign countries. Anyone anywhere can now use the digital currency to purchase anything offered by Overstock, from phone accessories to lawn furniture—though there are certain countries where the company doesn’t ship purchases. “As long as you can get on the internet, you can order and pay in bitcoin,” says Overstock founder and CEO Patrick Byrne. “You can order in North Korea if you want—as long as you’re having things delivered to, say, Singapore.”

    Online retailers Newegg and TigerDirect already accept bitcoin in both the U.S. and Canada, and smaller operations use bitcoin for international transactions, but Overstock, a company with $1.3 billion in annual sales, is stretching the reach of the digital currency still farther. Many questions hover over the future of bitcoin, a new type of money overseen by software running on across a vast network of machines. It’s still unclear how the governments of the world will regulate use of the currency. But it continues to evolve.

    Today, even bitcoin’s biggest supporters tend to hoard their bitcoin rather than spend them, seeing the digital currency, whose price is volatile, as more of an investment than anything else. But with Overstock expanding globally—and companies such as Dell considering similar arrangements—it’s getting easier to actually pay for stuff with bitcoin. “This seems to be great news,” says Roger Ver, one of bitcoin’s biggest supporters, whose computer-parts site, Memory Dealers, has accepted the digital currency for years.
    The Byrne Crusade

    Overstock’s move into the world of bitcoin is driven by Byrne. A libertarian with a PhD in philosophy, Byrne, like many others, sees bitcoin as a way to free our money system from the sometimes onerous and expensive control of big banks and big government. He recently vowed to take 4 percent of all Overstock bitcoin sales and donate it to non-profits working to further the cause of the digital currency, and he’s exploring ways the technology behind bitcoin could be used to issue stock in his company—without the help of traditional stock exchanges like the NASDAQ or the NYSE.

    “We swim in assumptions about how things should work, and we don’t understand the assumptions,” Byrne says, in his typically highfalutin way. “We don’t understand the functions of governments, our legal and financial institutions. We don’t need them. We can use internet.”



    Bitcoin is already an international technology. Part of the attraction has always been that the open source bitcoin network lets anyone transfer money across borders without paying hefty fees to traditional operations like Western Union. But in order to achieve mainstream acceptance, it must spread to a new breed of online service—easy-to-use services run by trusted businesses, as opposed to rather amateur operations run by the likes of the bankrupt bitcoin exchange Mt. Gox. Overstock’s move into bitcoin is a step along this road, and other notable businesses are helping to legitimize the digital currency in other ways.

    As Overstock began accepting international payments in bitcoin, Coinbase—the San Francisco-based startup whose technology drives these payments for Byrne and company—expanded its operation into 13 countries in Europe, and this could spark greater bitcoin adoption among merchants based there. Backed by $25 million in funding from big-name Silicon Valley venture capital firm Andressen Horowitz, Coinbase already drives bitcoin payments for eight American retailers that boast over a billion dollars a year in sales. Another notable bitcoin payments processor, BitPay, is offering its own services in Europe, and according to Moe Levin, the company’s director of European business development, about 200 new merchants are adopting the company’s service each week, compared to 200 a month as of April.

    At the sane time, Coinbase is now offering Europe a consumer service that lets individuals easily send, receive, and store their bitcoin. This can help drive bitcoin purchases from the other side of the equation, and as Coinbase founder and CEO Brian Armstrong points, that’s just as important to the evolution of the currency.
    The Bottom Line

    Bitcoin can potentially help consumers more easily and more cheaply store and spend money, but it can also provide a shot in the arm for merchants like Overstock. As Byrne points out, accepting credit card payments—particularly from foreign countries—is rather expensive, due to steep fees from third-party processors. “International credit cards are a real mess,” Byrne says. “If you’re taking cards from a place like Russia, there is a monster surcharge tacked on because so much credit card fraud comes from there.” Overstock still pays Coinbase to handle these transactions, but according to Byrne, these fees are significantly lower.

    Bitcoin payments have accounted for about one quarter of one percent of Overstock’s sales since January, or between $12,000 and $15,000 a day. Byrne calls this “a little bit more than I expected,” and he believes that with the company opening up bitcoin payments worldwide, the digital currency could drive a total of $8 million in sales by the end of the year. That’s not exactly a huge portion of the company’s revenues, but Byrne also believes bitcoin can become a way to expand the reach of his site. “We’ve never had a strong international business,” Byrne says, “and this is a good first step towards building one.”

    The rub is that government regulations—or just the threat of government regulations—could stunt the growth of bitcoin. Although the open source bitcoin system operates outside the control of governments and banks, some governments are working to strictly regulate the digital currency in their jurisdictions. New York state recently proposed the creation of a bitcoin license for businesses that would require them to report enormous amounts of information if operating in the state, and many believe this will prove too onerous for companies looking to deal in the digital currency. But Byrne is among those who believe regulators will find a way to accommodate the greater bitcoin movement. “Bitcoin has already become too big to fail,” he says. “This is not a genie they can put back into the bottle.”
    http://www.wired.com/2014/09/oversto...oin-worldwide/
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  6. The Following 5 Users Say Thank You to TargeT For This Post:

    Cara (4th December 2015), meeradas (15th October 2014), seko (4th October 2014), sigma6 (27th October 2014), Star Tsar (5th November 2014)

  7. Link to Post #84
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Quote The end of RUST? 'Wonder' paint made from graphene will stop any object from corroding, scientists say
    A 'wonder' paint made from graphene could banish rust forever, scientists claim.

    By combining it with oxygen they say they can create graphene oxide that, when applied as paint, provides an ultra-strong and non-corrosive coating.

    And the breakthrough could apparently revolutionise the medical, nuclear and even transport industries.

    raphene is a one atom thick sheet of carbon that has often been heralded as a 'miracle material'.

    This latest study by scientists from Manchester University created coatings for metals or even bricks that behave like graphite in terms of chemical and thermal stability.

    But they also become mechanically nearly as tough as graphene, the strongest material known to be in existence today.

    The team led by Dr Rahul Nair and Nobel laureate Sir Andre Geim demonstrated previously that multilayer films made from graphene oxide are vacuum tight under dry conditions.
    If exposed to water or its vapour however they act as molecular sieves, allowing passage of small molecules below a certain size.

    The findings could also have huge implications for water purification.

    This contrasting property is due to the structure of graphene oxide films that consist of millions of small flakes stacked randomly on top of each other but leave nano-sized capillaries between them.

    Water molecules inside these nanocapillaries and can drag small atoms and molecules along.

    In an article published in Nature Communications, the team showed it was possible to tightly close those nanocapillaries using simple chemical treatments, which makes graphene films even stronger mechanically as well as completely impermeable to everything: gases, liquids or strong chemicals.

    For example, they demonstrated that glassware or copper plates covered with graphene paint can be used as containers for strongly corrosive acids.

    The exceptional barrier properties of graphene paint have already attracted interest from many companies who now collaborate with The University of Manchester on development of new protective and anticorrosion coatings.

    Dr Nair said: 'Graphene paint has a good chance to become a truly revolutionary product for industries that deal with any kind of protection either from air, weather elements or corrosive chemicals.

    'Those include, for example, medical, electronics and nuclear industry or even shipbuilding, to name but the few.'

    Another author on the research Dr Yang Su added: 'Graphene paint can be applied to practically any material, independently of whether it's plastic, metal or even sand.

    'For example, plastic films coated with graphene could be of interest for medical packaging to improve shelf life because they are less permeable to air and water vapour than conventional coatings. In addition, thin layers of graphene paint are optically transparent.'
    Read more: http://www.dailymail.co.uk/sciencete...#ixzz3D2MHKzeP
    Follow us: @MailOnline on Twitter | DailyMail on Facebook
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  8. The Following 5 Users Say Thank You to TargeT For This Post:

    animovado (15th October 2014), Cara (4th December 2015), fourty-two (11th September 2014), meeradas (15th October 2014), Star Tsar (5th November 2014)

  9. Link to Post #85
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Witricity is a wireless magnetic resonance induction system with some pretty impressive results, it's not Tesla's idea of wireless power but it works and is a pretty cool application.

    Power cords might be extinct soon.




    This is closer to what Tesla envisioned, but apparently it's not as refined as Witricity above & has some limitations that will hurt the technology if they cannot be overcome:

    Quote The WattUp transmitter works much like a wireless router, sending radio frequency signals that can be received by enabled mobile devices, such as wearables and mobile phones. A small RF antenna in the form of PCB board, an ASIC and software makes up the wireless power receivers.

    The Bluetooth wireless communication specification is used between WattUp transmitters and receivers.

    Because the amount of wattage it can send is limited, Energous is focused on small mobile devices rather than laptops or batteries that require higher capacities.

    A single WattUp transmitter can charge up to 24 devices, all under software control that enables or disables charging. The maximum amount of power -- four watts -- can only be delivered to four devices simultaneously. So as more enabled and "authorized" devices enter a room, the charge to each device is reduced.
    http://www.computerworld.com/article...e-devices.html

    Last edited by TargeT; 15th September 2014 at 16:39.
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  10. The Following 6 Users Say Thank You to TargeT For This Post:

    Agape (15th September 2014), animovado (15th October 2014), Cara (4th December 2015), fourty-two (15th September 2014), meeradas (15th October 2014), Star Tsar (5th November 2014)

  11. Link to Post #86
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Quote Batteries Included: A Solar Cell that Stores its Own Power
    World’s first “solar battery” runs on light and air
    “The state of the art is to use a solar panel to capture the light, and then use a cheap battery to store the energy,” Wu said. “We’ve integrated both functions into one device. Any time you can do that, you reduce cost.”

    He and his students believe that their device brings down costs by 25 percent.

    The invention also solves a longstanding problem in solar energy efficiency, by eliminating the loss of electricity that normally occurs when electrons have to travel between a solar cell and an external battery. Typically, only 80 percent of electrons emerging from a solar cell make it into a battery.

    With this new design, light is converted to electrons inside the battery, so nearly 100 percent of the electrons are saved.
    The design takes some cues from a battery previously developed by Wu and doctoral student Xiaodi Ren. They invented a high-efficiency air-powered battery that discharges by chemically reacting potassium with oxygen. The design won the $100,000 clean energy prize from the U.S. Department of Energy in 2014, and the researchers formed a technology spinoff called KAir Energy Systems, LLC to develop it.

    “Basically, it’s a breathing battery,” Wu said. “It breathes in air when it discharges, and breathes out when it charges.”
    http://news.osu.edu/news/2014/10/03/...its-own-power/




    Quote An Australian researcher has worked out how to store 1000TB on a CD

    A young Victorian researcher has made a breakthrough in optical formatting that could significantly increase our data storage capacity.



    Every day, humans are producing more data than ever before - around 90% of the world’s data was generated in the past two years alone - and there will come a point when our data storage centres and the cloud can no longer keep up.

    But Dr Zongsong Gan, a researcher at Swinburne University of Technology in Melbourne, Australia, has found a revolutionary way we can fit a whole lot more data onto traditional optical storage devices, such as CDs, and is now using that technology to help data storage keep up with demand.

    In 2013, Gan and his colleagues found out how to fit 1,000 terabytes (TB), or 50,000 high-definition movies, onto a DVD - an increase from the 4.07 gigabytes they’re currently capable of storing. And he’s now been awarded one of 12 Victoria Fellowships in 2014, which will help incorporate his research into practical, mass storage devices.

    Gan and his colleagues managed to increase DVD storage so significantly by using light to create extra small dots or ‘bits’ - the unit used to store information. This means they could write far more information than ever before onto discs the same size.

    This advance required them breaking a physical barrier known as the diffraction limit of light. Light cannot be split any smaller than around 500 nanometres, and before their work it was thought that, because of this, light wasn't capable of writing bits of information smaller than 500 nanometres across.

    But by using two-light-beams with different abilities, the scientists managed to whittle down the point of light writing the data to just nine nanometres across, or one ten thousandth the diameter of a human hair.

    Both the beams used were 500-nanometres-wide, but one was for writing information (red), and the other beam (purple) blocked the first from writing information. By making the second one doughnut-shaped, they created only a small space that the first beam could write information through, as shown in the image above.

    With the $18,000 fellowship, Gan will collaborate with industry and researchers around the world to work on new breakthroughs for data storage devices, and also see how his existing research can be used on a larger scale to rapidly improve the capacity of optics-based information technologies.

    “The successful development of our technology will result in possible Victorian owned long-term patents and create a global role for Victoria, reinforcing the state’s profile of fostering high-tech industry and an innovative research environment, in particular in optics-based information technologies,”
    http://www.sciencealert.com.au/news/20140309-26116.html
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  12. The Following 6 Users Say Thank You to TargeT For This Post:

    animovado (15th October 2014), Blake Elder (12th October 2014), Cara (4th December 2015), meeradas (15th October 2014), seko (4th October 2014), sigma6 (27th October 2014)

  13. Link to Post #87
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Around 10% of all diabetes is Type 1, & 29 million people in the United States have diabetes; so 2.9 million people could be cured by this.

    Quote Cure for Type 1 diabetes imminent after Harvard stem-cell breakthrough

    A cure for diabetes could be imminent after scientists discovered how to make huge quantities of insulin-producing cells, in a breakthrough hailed as significant as antibiotics.
    Harvard University has, for the first time, managed to manufacture the millions of beta cells required for transplantation.
    It could mean the end of daily insulin injections for the 400,000 people in Britain living with Type 1 diabetes.
    And it marks the culmination of 23-years of research for Harvard professor Doug Melton who has been trying to find a cure for the disease since his son Sam was diagnosed with Type 1 diabetes as a baby.“We are now just one pre-clinical step away from the finish line,” said Prof Melton.
    Asked about his children’s reaction he said: "I think like all kids, they always assumed that if I said I'd do this, I'd do it,
    "It was gratifying to know that we can do something that we always thought was possible.”
    The stem cell-derived beta cells are presently undergoing trials in animal models, including non-human primates, where they are still producing insulin after several months, Prof Melton said.
    Type 1 diabetes is an autoimmune condition that causes the pancreas to stop producing insulin - the hormone that regulates blood glucose levels.
    If the amount of glucose in the blood is too high it can seriously damage the body's organs over time.
    While diabetics can keep their glucose levels under general control by injecting insulin, that does not provide the fine tuning necessary to properly control metabolism, which can lead to devastating complications such as blindness or loss of limbs.Around 10 per cent of all diabetes is Type 1, but it is the most common type of childhood diabetes. 29,000 youngsters suffer in Britain.
    The team at Harvard used embryonic stem cells to produce human insulin-producing cells equivalent in almost every way to normally functioning cells in vast quantities.
    Chris Mason, Professor of Regenerative Medicine, University College London, said it was ‘potentially a major medical breakthrough.’
    “If this scalable technology is proven to work in both the clinic and in the manufacturing facility, the impact on the treatment of diabetes will be a medical game-changer on a par with antibiotics and bacterial infections,” he said.
    Professor Anthony Hollander, Head of Institute of Integrative Biology at the University of Liverpool, added:“This is very exciting fundamental research that solves a major roadblock in the development of a stem cell treatment for diabetes.
    “The study provides a very elegant and convincing method for generating functional insulin-producing cells in large numbers.”
    Professor Mark Dunne, at Manchester University, added: Overall this is an important advance for the field of diabetes and people with Type 1 diabetes.”
    Professor Elaine Fuchs, of Rockefeller University, described the findings as "one of the most important advances to date in the stem cell field".
    "For decades, researchers have tried to generate human pancreatic beta cells that could be cultured and passaged long term under conditions where they produce insulin.”
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  14. The Following 5 Users Say Thank You to TargeT For This Post:

    Blake Elder (12th October 2014), Cara (4th December 2015), meeradas (15th October 2014), sigma6 (27th October 2014), Star Tsar (5th November 2014)

  15. Link to Post #88
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Quote This Device Could Detect Dozens of Cancers With a Single Blood Test

    Early detection, we’re often told, is the surest way to beat cancer. It’s the reason why, year after year, men and women of a certain age dutifully visit their doctors and undergo uncomfortable tests to screen for things like prostate and breast cancer.

    But what about the other hundred or so types of cancer out there—the brain cancers, the ovarian cancers, the leukemias and lymphomas? And what of the millions of young people who never get tested at all, even though they’ve been found to have worse outcomes than adults?

    Current diagnostic methods for other cancers are invasive and expensive, so the vast majority of cancer patients never realize they might have cancer until something goes wrong with their health. By that point, in many cases, it’s already too late.

    MIROCULUS COULD MAKE REGULAR CANCER SCREENINGS AS SIMPLE AS GETTING BLOOD DRAWN.
    That’s why a new startup, dubbed Miroculus, is building a device that could easily and affordably check for dozens of cancers using a single blood sample. Known as Miriam, this low-cost, open source device made its public debut at the TEDGlobal conference in Rio De Janeiro on Thursday, with TED curator Chris Anderson calling it “one of the most thrilling demos in TED history.”

    For the company’s founders—a global team of entrepreneurs, microbiologists, and data scientists—the goal is to make Miriam so simple that even untrained workers in clinics around the world could use it. The project is still in the early stages, but if the early trials of Miriam are to be believed, Miroculus could make regular cancer screenings as simple as getting blood drawn.

    A Biological Warning Sign
    The Miroculus technology is based on microRNA, a class of small molecules that can act as a type of biological warning sign, appearing and disappearing based on what is happening in our bodies at that moment. As a result, they’ve become effective indicators of diseases—including cancer—ever since they were first discovered in 1993. They can reveal not just whether a person may have cancer, but what specific type of cancer that person might have.

    For years, however, researchers believed microRNA could only be found inside of cells, making these biomarkers less accessible. But in 2008, a group of researchers discovered microRNA circulating in blood, spawning a wave of interest from other scientists, who viewed microRNA as the key to early cancer detection.

    Fay Christodoulou was one such researcher. After spending years studying microRNA’s effects on evolution, Christodoulou, a Greek molecular biologist, shifted her focus to study the connection between microRNA and thyroid cancer. Last year, she decided to take some time off to enter a graduate studies program at Singularity University, a Silicon Valley incubator that challenges people to spend 10 weeks developing a business idea with the power to impact one billion people or more.

    It was there that she met Alejandro Tocigl, a Chilean entrepreneur; Gilad Gome, an Israeli biotechnologist; Pablo Olivares, a Chilean doctor; Ferrán Galindo, a serial entrepreneur from Panama; and Jorge Soto, a Mexican electronic engineer and former general director of civic innovation for the Mexican government. Together, they formed a team and developed the bones of what would eventually become Miriam.

    “In 10 weeks, to make something from nothing is practically impossible. But what they teach you—in my personal case, for the first time in my life—was in order to disrupt, you don’t need to do 10 years of research,” Christodoulou says. “You’re capable of using pre-existing tools but combining them in a way no one had thought of before.”
    Not Reinventing the Wheel
    Miriam capitalizes on much of the research and science that already exists around microRNA and cancer. You can prepare the blood sample, for instance, using a standard off-the-shelf RNA extraction kit, as well as a Miroculus “master mix” (another means of preparing the raw sample for the test). Then, once the sample is prepared, you pipette the blood into a 96-well plate, which Christodoulou refers to as the company’s “secret sauce.”

    That’s because each well has been pre-treated with Miroculus’s patented biochemistry to act as a sort of trap for various types of microRNA, most commonly associated with cancer. When Miroculus goes to market, it will be these plates—and not the $500 devices themselves—that will generate the most revenue.

    After the wells are full, the plate goes into the device, and the reaction begins. When microRNA is present, the wells start to glow. The stronger the glow, the stronger the presence of microRNA. In an hour, the reaction is complete, and the results get sent to a cloud server. There, the system reads the luminosity of the various wells, determines which microRNA is present in the sample, and compares that result to a database of information on which microRNA patterns are associated with which cancers. Then the system is able to make a judgment.

    While at Singularity, the team completed a proof of principle experiment, in which they successfully detected liver cancer in mice. But that, says Christodoulou, is just the first step in a long process of proving the technology works. “We’re talking about a decentralized system; the main challenge is to make it robust enough so it can be done by an untrained person anywhere in the world in not-so-optimal laboratory conditions,” she says.

    Data, Data, and More Data
    The company—which is now run full-time by Tocigl, Christodoulou, and Soto—must also build its database to ensure the system can read the results accurately. According to Muneesh Tewari, who heads up his own research lab at the Fred Hutchinson Cancer Research Center and was part of the team that first discovered microRNA in blood, that will take some doing.

    The challenge with microRNA, he says, is that it doesn’t only show up in the case of cancer. Something as simple as taking aspirin or having a respiratory infection could affect which microRNA gets expressed in blood. To guarantee accuracy, Miroculus’s technology must know not only which results mean cancer, but also how other health conditions, medications, and environmental factors can alter or inhibit those results.

    “There are so many stories of biomarkers that get discovered, and then there are things you didn’t know that basically kill the marker,” Tewari says. “Bringing the device to the point where, in fact, it is robust and reliable when you put it in the hands of a large number of people who are truly untrained, that’s always the next barrier to be overcome.”

    SOMETHING AS SIMPLE AS TAKING ASPIRIN OR HAVING A RESPIRATORY INFECTION COULD AFFECT WHICH MICRORNA GETS EXPRESSED IN BLOOD.
    The Miroculus team understands that data is, in some ways, just as important to Miriam’s success as the science behind it. “We’re a data-driven company, and we believe our value will be in the information we gather, how we correlate the information, and the conclusions we’re able to make,” says Tocigl.

    That’s one reason why Miroculus is launching the product not with the doctors and clinics—it would require FDA approval for that, anyway—but with pharmaceutical companies, who will use the tool to track how patients react to new drugs. As these companies track results, Miroculus will, in turn, be able to collect mountains of microRNA related data. Once that trove of information is robust enough, and that could take a number of years, then and only then will Miroculus begin to seek FDA approval to market Miriam as a diagnostic tool. Until then, Miroculus will continue tweaking the device and running its own studies out of the European Molecular Biology Lab in Heidelberg, Germany.

    A New Definition of Cancer
    Tewari says this method is a smart one, and he credits Miroculus for taking a Silicon Valley approach to the problem, forging ahead with the technology, even while the research that powers it is ongoing. “I think these tracks need to move in parallel,” he says. “I think you need both before we change the world.”

    And yet, he brings up an interesting point, and that is the fact that early detection, long considered the only real cure for cancer, is now the subject of heated debate in the medical community. It’s become so pointed that last year, a group of experts at the National Cancer Institute went as far as to call for a new definition of the word “cancer.”

    Their argument was that science has come so far that some conditions we still refer to as cancer are basically harmless, such as ductal carcinoma in situ, a non-invasive type of breast cancer. In continuing to call them cancer, they say, society is only causing patients undue stress, and that leads, in many cases to undue surgeries and treatments, as well. Routine cancer screenings like the one Miroculus suggests could, theoretically, create the problem of over-diagnosis of indolent cancers, Tewari says.

    “Early detection can have a massive impact on mortality in the world,” he says, “but one can’t be too naïve about the real issues related to the problem of early detection, either.”

    Still, he says, it’s important not to allow this fear to inhibit the development of novel new ways of catching cancer early. “The idea of having a system, that really performs well, that’s very robust and can be done at the point of care, without an expert,” Tewari says, pausing. “Well, that idea is very powerful, and important, and could really be potentially transformative.”
    http://www.wired.com/2014/10/miroculus/?mbid=social_fb
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  16. The Following 5 Users Say Thank You to TargeT For This Post:

    Cara (4th December 2015), meeradas (15th October 2014), NancyV (15th October 2014), sigma6 (27th October 2014), Star Tsar (5th November 2014)

  17. Link to Post #89
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    We have seen this before, it appears to be more refined now, perhaps MUCH closer to production:
    Quote Heat scavengers promise energy bonanza
    A new breed of structures called skutterudites could finally tap the floods of energy our machines waste as heat

    Thermodynamics will always take its pound of flesh. Its laws ultimately dictate that more than half of the energy we use in cars, dishwashers, factories and elsewhere is lost as waste heat. That's just an average: for car engines, the proportion is more like two-thirds.
    Reclaim even a small amount of that lost heat as electricity, and that would massively boost energy efficiency. Thermoelectric materials allow us to do just that, by coaxing a current from a temperature difference. Wrap a thermoelectric substance around your car's exhaust, and its waste heat could power the electrics. Incorporate thermoelectric elements into a refrigerator, and heat extracted from its interior could power it.
    http://www.newscientist.com/article/...13-GLOBAL-hoot

    http://journals.aps.org/prb/abstract...RevB.89.184304



    Quote MIT's Self-Assembly Lab has developed materials that can be programmed to transform their shape autonomously -- from flexible carbon fibre and hybrid plastics to wood grains and textiles.

    Skylar Tibbits, director of Self-Assembly Lab and research scientist at MIT -- as well as one of the WIRED2014 Innovation Fellows -- spoke to WIRED.co.uk exclusively about his research lab's latest discoveries with these programmable materials.

    "The idea here is to take existing material systems like fibres, sheets, strands and three-dimensional objects and program them to change shape and property on demand," Tibbits explains. "It's sort of like a vision of a robots without wire, motors or batteries."

    Tibbits spoke at TED in 2013 about the emergence of 4D printing, where he demonstrated materials that reacted to passive energy sources like water, folding twisting to a programmed shape. "We released it at TED the response totally blew us away," Tibbits says. "A lot of people wanted to write about it, and a lot of people were excited about it. More importantly a lot of companies came to us, and saw applications that we never would've expected."
    http://www.wired.co.uk/news/archive/...sive-interview

    Quote
    Fast-charging batteries will power your gadgets for 20 years


    Fast-charging batteries are all nice and good, but the lifespan matters, too -- why should you have to replace power packs (or entire devices) every couple of years ? You may not have to give up performance or longevity if researchers at Nanyang Technology University have their way. They've developed new lithium ion batteries that can reach a 70 percent charge in two minutes, but should also last for over 20 years -- several times longer than the cells in your current laptop or smartphone. The trick is using titanium dioxide nanotubes for the anode (the negative pole) instead of graphite; they both speed up the battery's chemical reactions while offering 10,000 charging cycles instead of the usual 500.
    There's no definite timetable for when upgraded batteries could reach shipping products, but the mini titanium tubes are both easy to make and relatively inexpensive. They could make a big impact on the technology world when they arrive, though. On a basic level, they could eliminate forced obsolescence for some devices -- you might only replace them when they no longer meet your needs, not because they can't hold a charge. They could have a particularly large impact on electric cars -- you could top up your battery in minutes, not hours, and avoid replacing a very expensive component before you're ready to replace the vehicle itself.
    http://www.engadget.com/2014/10/13/f...=rss_truncated

    Quote Samsung achieves Wi-Fi data travel feats for 60GHZ band
    Samsung Electronics has announced advances in Wi-Fi technology. Samsung said it found a way to make Wi-Fi data travel faster than it does currently. Specifically, Samsung said the new technology enables data transmission speeds of up to 4.6Gbps, or 575MB per second, a fivefold increase from 866Mbps, or 108MB per second, which the company said was the maximum speed possible with existing consumer electronics devices. Eventually, consumers will see the results of these efforts within various connected devices.
    BBC News said the faster Wi-Fi could make it fast to stream movies from phones to TVs and other displays. A 1GB movie will take less than three seconds to transfer between devices, said Samsung. Samsung Electronics refers to the development as its "60GHz Wi-Fi technology." The company's engineers worked on Wi-Fi that operated in the 60GHz band, whereas current Wi-Fi systems use 2.4 and 5GHz bands, said the BBC. This is news in itself, as Samsung has successfully overcome some barriers to the commercialization of the 60GHz millimeter-wave band Wi-Fi technology, said Kim Chang Yong, Head of DMC R&D Center of Samsung Electronics. In the press release, the company said, "Unlike the existing 2.4GHz and 5GHz Wi-Fi technologies, Samsung's 802.11ad standard 60GHz Wi-Fi technology maintains maximum speed by eliminating co-channel interference, regardless of the number of devices using the same network."

    "Samsung has Invented a No-Interference, 60GHz Wi-Fi," said the Windows IT Pro headline on Monday. Rod Trent of Windows IT Pro wrote that "the 802.11ad technology also maintains maximum speed by eliminating co-channel interference. If you've worked with Wi-Fi for very long, you know that speeds can vary because the signal is constantly negotiating with other technologies in the near area that are utilizing the same channels."
    http://phys.org/news/2014-10-samsung...-band.html#jCp
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  18. The Following 6 Users Say Thank You to TargeT For This Post:

    animovado (15th October 2014), Cara (4th December 2015), meeradas (15th October 2014), NancyV (15th October 2014), sigma6 (27th October 2014), Star Tsar (5th November 2014)

  19. Link to Post #90
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Quote Skunk Works Reveals Compact Fusion Reactor Details
    Lockheed Martin aims to develop compact reactor prototype in five years, production unit in 10

    Hidden away in the secret depths of the Skunk Works, a Lockheed Martin research team has been working quietly on a nuclear energy concept they believe has the potential to meet, if not eventually decrease, the world’s insatiable demand for power.

    Dubbed the compact fusion reactor (CFR), the device is conceptually safer, cleaner and more powerful than much larger, current nuclear systems that rely on fission, the process of splitting atoms to release energy. Crucially, by being “compact,” Lockheed believes its scalable concept will also be small and practical enough for applications ranging from interplanetary spacecraft and commercial ships to city power stations. It may even revive the concept of large, nuclear-powered aircraft that virtually never require refueling—ideas of which were largely abandoned more than 50 years ago because of the dangers and complexities involved with nuclear fission reactors.

    Yet the idea of nuclear fusion, in which atoms combine into more stable forms and release excess energy in the process, is not new. Ever since the 1920s, when it was postulated that fusion powers the stars, scientists have struggled to develop a truly practical means of harnessing this form of energy. Other research institutions, laboratories and companies around the world are also pursuing ideas for fusion power, but none have gone beyond the experimental stage. With just such a “Holy Grail” breakthrough seemingly within its grasp, and to help achieve a potentially paradigm-shifting development in global energy, Lockheed has made public its project with the aim of attracting partners, resources and additional researchers.

    Although the company released limited information on the CFR in 2013, Lockheed is now providing new details of its invention. Aviation Week was given exclusive access to view the Skunk Works experiment, dubbed “T4,” first hand. Led by Thomas McGuire, an aeronautical engineer in the Skunk Work’s aptly named Revolutionary Technology Programs unit, the current experiments are focused on a containment vessel roughly the size of a business-jet engine. Connected to sensors, injectors, a turbopump to generate an internal vacuum and a huge array of batteries, the stainless steel container seems an unlikely first step toward solving a conundrum that has defeated generations of nuclear physicists—namely finding an effective way to control the fusion reaction.

    “I studied this in graduate school where, under a NASA study, I was charged with how we could get to Mars quickly,” says McGuire, who earned his Ph.D. at the Massachusetts Institute of Technology. Scanning the literature for fusion-based space propulsion concepts proved disappointing. “That started me on the road and [in the early 2000s], I started looking at all the ideas that had been published. I basically took those ideas and melded them into something new by taking the problems in one and trying to replace them with the benefits of others. So we have evolved it here at Lockheed into something totally new, and that’s what we are testing,” he adds.

    To understand the breakthroughs of the Lockheed concept, it is useful to know how fusion works and how methods for controlling the reaction have a fundamental impact on both the amount of energy produced and the scale of the reactor. Fusion fuel, made up of hydrogen isotopes deuterium and tritium, starts as a gas injected into an evacuated containment vessel. Energy is added, usually by radio-frequency heating, and the gas breaks into ions and electrons, forming plasma.

    The superhot plasma is controlled by strong magnetic fields that prevent it from touching the sides of the vessel and, if the confinement is sufficiently constrained, the ions overcome their mutual repulsion, collide and fuse. The process creates helium-4, freeing neutrons that carry the released energy kinetically through the confining magnetic fields. These neutrons heat the reactor wall which, through conventional heat exchangers, can then be used to drive turbine generators.

    Until now, the majority of fusion reactor systems have used a plasma control device called a tokamak, invented in the 1950s by physicists in the Soviet Union. The tokamak uses a magnetic field to hold the plasma in the shape of a torus, or ring, and maintains the reaction by inducing a current inside the plasma itself with a second set of electromagnets. The challenge with this approach is that the resulting energy generated is almost the same as the amount required to maintain the self-sustaining fusion reaction.

    An advanced fusion reactor version, the International Thermonuclear Experimental Reactor (ITER), being built in Cadarache, France, is expected to generate 500 MW. However, plasma is not due to be generated until the late 2020s, and derivatives are not likely to be producing significant power until at least the 2040s.

    The problem with tokamaks is that “they can only hold so much plasma, and we call that the beta limit,” McGuire says. Measured as the ratio of plasma pressure to the magnetic pressure, the beta limit of the average tokamak is low, or about “5% or so of the confining pressure,” he says. Comparing the torus to a bicycle tire, McGuire adds, “if they put too much in, eventually their confining tire will fail and burst—so to operate safely, they don’t go too close to that.” Aside from this inefficiency, the physics of the tokamak dictate huge dimensions and massive cost. The ITER, for example, will cost an estimated $50 billion and when complete will measure around 100 ft. high and weigh 23,000 tons.

    The CFR will avoid these issues by tackling plasma confinement in a radically different way. Instead of constraining the plasma within tubular rings, a series of superconducting coils will generate a new magnetic-field geometry in which the plasma is held within the broader confines of the entire reaction chamber. Superconducting magnets within the coils will generate a magnetic field around the outer border of the chamber. “So for us, instead of a bike tire expanding into air, we have something more like a tube that expands into an ever-stronger wall,” McGuire says. The system is therefore regulated by a self-tuning feedback mechanism, whereby the farther out the plasma goes, the stronger the magnetic field pushes back to contain it. The CFR is expected to have a beta limit ratio of one. “We should be able to go to 100% or beyond,” he adds.

    This crucial difference means that for the same size, the CFR generates more power than a tokamak by a factor of 10. This in turn means, for the same power output, the CFR can be 10 times smaller. The change in scale is a game-changer in terms of producibility and cost, explains McGuire. “It’s one of the reasons we think it is feasible for development and future economics,” he says. “Ten times smaller is the key. But on the physics side, it still has to work, and one of the reasons we think our physics will work is that we’ve been able to make an inherently stable configuration.” One of the main reasons for this stability is the positioning of the superconductor coils and shape of the magnetic field lines. “In our case, it is always in balance. So if you have less pressure, the plasma will be smaller and will always sit in this magnetic well,” he notes.

    Overall, McGuire says the Lockheed design “takes the good parts of a lot of designs.” It includes the high beta configuration, the use of magnetic field lines arranged into linear ring “cusps” to confine the plasma and “the engineering simplicity of an axisymmetric mirror,” he says. The “axisymmetric mirror” is created by positioning zones of high magnetic field near each end of the vessel so that they reflect a significant fraction of plasma particles escaping along the axis of the CFR. “We also have a recirculation that is very similar to a Polywell concept,” he adds, referring to another promising avenue of fusion power research. A Polywell fusion reactor uses electromagnets to generate a magnetic field that traps electrons, creating a negative voltage, which then attract positive ions. The resulting acceleration of the ions toward the negative center results in a collision and fusion.

    The team acknowledges that the project is in its earliest stages, and many key challenges remain before a viable prototype can be built. However, McGuire expects swift progress. The Skunk Works mind-set and “the pace that people work at here is ridiculously fast,” he says. “We would like to get to a prototype in five generations. If we can meet our plan of doing a design-build-test generation every year, that will put us at about five years, and we’ve already shown we can do that in the lab.” The prototype would demonstrate ignition conditions and the ability to run for upward of 10 sec. in a steady state after the injectors, which will be used to ignite the plasma, are turned off. “So it wouldn’t be at full power, like a working concept reactor, but basically just showing that all the physics works,” McGuire says.

    An initial production version could follow five years after that. “That will be a much bigger effort,” he says, suggesting that transition to full-scale manufacturing will necessarily involve materials and heat-transfer specialists as well as gas-turbine makers. The early reactors will be designed to generate around 100 MW and fit into transportable units measuring 23 X 43 ft. “That’s the size we are thinking of now. You could put it on a semi-trailer, similar to a small gas turbine, put it on a pad, hook it up and can be running in a few weeks,” McGuire says. The concept makes use of the existing power infrastructures to enable the CFR to be easily adapted into the current grid. The 100-MW unit would provide sufficient power for up to 80,000 homes in a power-hungry U.S. city and is also “enough to run a ship,” he notes.

    Lockheed estimates that less than 25 kg (55 lb.) of fuel would be required to run an entire year of operations. The fuel itself is also plentiful. Deuterium is produced from sea water and is therefore considered unlimited, while tritium is “bred” from lithium. “We already mine enough lithium to supply a worldwide fleet of reactors, so with tritium you never have too much built up, and that’s what keeps it safe. Tritium would be a health risk if there were enough released, but it is safe enough in small quantities. You don’t need very much to run a reactor because it is a million times more powerful than a chemical reaction,” McGuire notes.

    Although the first-generation reactors will have radioactive parts at the ends of their lives, such as some steel elements in the shell, McGuire says the contamination situation “is an order of magnitude better” than that of contemporary fission systems. “There is no long-lived radiation. Fission reactors’ stuff will be there forever, but with fusion materials, after 100 years then you are good.” Contamination levels for fusion will improve with additional materials research, he believes. “It’s been a chicken-and-egg situation. Until we’ve had a good working fusion system, there has not been money to go off and do the hard-core materials research,” McGuire says. “So we believe the first generation is good enough to go out and do, and then it will only improve in time.” Old CFR steel shell parts can be disposed of with “a shallow burial in the desert, similar to medical waste today. That’s a major difference to today’s fission systems.”

    Operational benefits include no risks of suffering a meltdown. “There is a very minimal amount of radioactive tritium—it’s on the order of grams—so the potential release is very minimal. In addition, there is not enough to be a risk of proliferation. Tritium is used in nuclear weapons but in a much larger inventory than would be involved here, and that’s because you are continually making just enough to feed back in [to maintain the reaction],” he adds.

    Preliminary simulations and experimental results “have been very promising and positive,” McGuire says. “The latest is a magnetized ion confinement experiment, and preliminary measurements show the behavior looks like it is working correctly. We are starting with the plasma confinement, and that’s where we are putting most of our effort. One of the reasons we are becoming more vocal with our project is that we are building up our team as we start to tackle the other big problems. We need help and we want other people involved. It’s a global enterprise, and we are happy to be leaders in it.”
    http://aviationweek.com/technology/s...eactor-details
    http://aviationweek.com/blog/high-ho...-air-transport

    Quote Report: Samsung's Made Rollable Batteries That Bend Into a Hoop

    Wearables: great, apart from the fact that batteries last about five minutes. Samsung, though, may have a solution: it's just announced a new type of battery which is so flexible that it can be rolled up into a hoop.

    The announcement, made at InterBattery 2014 in Seoul—how about that for an expo name?—claims that the new style of battery can work even when it's rolled up into the shape of a paper cup. While details are scant according to a report by G for Games, the new flexibility apparently stems from changes in structural design and improved materials.

    It may be a little early to get too excited though: these things certainly aren't ready for the masses yet. Indeed, the reliability of the cells is apparently still low, which suggests that, even if they do work when deformed, that performance doesn't last for long.

    G for Games claims that "reports claim that the units will be commercially available within the next three years." But, even if that's accurate, three years is quite a long time; flying cars might exist in three year's time, to be honest. Still, it's a leap forwards in terms of battery design—let's just hope it arrives, from Samsung or anyone else for that matter, sooner than those reports suggest. [G for Games]
    http://gizmodo.com/report-samsungs-m...t-i-1646539094
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  20. The Following 6 Users Say Thank You to TargeT For This Post:

    animovado (15th October 2014), Cara (4th December 2015), meeradas (15th October 2014), NancyV (15th October 2014), sigma6 (27th October 2014), Star Tsar (5th November 2014)

  21. Link to Post #91
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Quote Researchers develop world's thinnest electric generator

    IMAGE: This is a cartoon showing positive and negative polarized charges are squeezed from a single layer of atoms of molybdenum disulfide (MoS2), as it is being stretched. Click here for more information.
    First experimental observation of piezoelectricity in an atomically thin material -- MoS2 -- could lead to wearable devices.

    Researchers from Columbia Engineering and the Georgia Institute of Technology report today that they have made the first experimental observation of piezoelectricity and the piezotronic effect in an atomically thin material, molybdenum disulfide (MoS2), resulting in a unique electric generator and mechanosensation devices that are optically transparent, extremely light, and very bendable and stretchable.

    In a paper published online October 15, 2014, in Nature, research groups from the two institutions demonstrate the mechanical generation of electricity from the two-dimensional (2D) MoS2 material. The piezoelectric effect in this material had previously been predicted theoretically.
    Piezoelectricity is a well-known effect in which stretching or compressing a material causes it to generate an electrical voltage (or the reverse, in which an applied voltage causes it to expand or contract). But for materials of only a few atomic thicknesses, no experimental observation of piezoelectricity has been made, until now. The observation reported today provides a new property for two-dimensional materials such as molybdenum disulfide, opening the potential for new types of mechanically controlled electronic devices.

    "This material—just a single layer of atoms—could be made as a wearable device, perhaps integrated into clothing, to convert energy from your body movement to electricity and power wearable sensors or medical devices, or perhaps supply enough energy to charge your cell phone in your pocket," says James Hone, professor of mechanical engineering at Columbia and co-leader of the research.

    "Proof of the piezoelectric effect and piezotronic effect adds new functionalities to these two-dimensional materials," says Zhong Lin Wang, Regents' Professor in Georgia Tech's School of Materials Science and Engineering and a co-leader of the research. "The materials community is excited about molybdenum disulfide, and demonstrating the piezoelectric effect in it adds a new facet to the material."

    Hone and his research group demonstrated in 2008 that graphene, a 2D form of carbon, is the strongest material. He and Lei Wang, a postdoctoral fellow in Hone's group, have been actively exploring the novel properties of 2D materials like graphene and MoS2 as they are stretched and compressed.

    IMAGE: Researchers from the Georgia Institute of Technology and Columbia Engineering have made the first experimental observation of piezoelectricity and the piezotronic effect in an atomically thin material, molybdenum disulfide (MoS2)....Click here for more information.
    Zhong Lin Wang and his research group pioneered the field of piezoelectric nanogenerators for converting mechanical energy into electricity. He and postdoctoral fellow Wenzhuo Wu are also developing piezotronic devices, which use piezoelectric charges to control the flow of current through the material just as gate voltages do in conventional three-terminal transistors.

    There are two keys to using molybdenum disulfide for generating current: using an odd number of layers and flexing it in the proper direction. The material is highly polar, but, Zhong Lin Wang notes, so an even number of layers cancels out the piezoelectric effect. The material's crystalline structure also is piezoelectric in only certain crystalline orientations.

    For the Nature study, Hone's team placed thin flakes of MoS2 on flexible plastic substrates and determined how their crystal lattices were oriented using optical techniques. They then patterned metal electrodes onto the flakes. In research done at Georgia Tech, Wang's group installed measurement electrodes on samples provided by Hone's group, then measured current flows as the samples were mechanically deformed. They monitored the conversion of mechanical to electrical energy, and observed voltage and current outputs.

    The researchers also noted that the output voltage reversed sign when they changed the direction of applied strain, and that it disappeared in samples with an even number of atomic layers, confirming theoretical predictions published last year. The presence of piezotronic effect in odd layer MoS2 was also observed for the first time.

    "What's really interesting is we've now found that a material like MoS2, which is not piezoelectric in bulk form, can become piezoelectric when it is thinned down to a single atomic layer," says Lei Wang.

    IMAGE: Researchers from the Georgia Institute of Technology and Columbia Engineering have made the first experimental observation of piezoelectricity and the piezotronic effect in an atomically thin material, molybdenum disulfide (MoS2).... Click here for more information.
    To be piezoelectric, a material must break central symmetry. A single atomic layer of MoS2 has such a structure, and should be piezoelectric. However, in bulk MoS2, successive layers are oriented in opposite directions, and generate positive and negative voltages that cancel each other out and give zero net piezoelectric effect.

    "This adds another member to the family of piezoelectric materials for functional devices," says Wenzhuo Wu.

    In fact, MoS2 is just one of a group of 2D semiconducting materials known as transition metal dichalcogenides, all of which are predicted to have similar piezoelectric properties. These are part of an even larger family of 2D materials whose piezoelectric materials remain unexplored. Importantly, as has been shown by Hone and his colleagues, 2D materials can be stretched much farther than conventional materials, particularly traditional ceramic piezoelectrics, which are quite brittle.

    The research could open the door to development of new applications for the material and its unique properties.

    "This is the first experimental work in this area and is an elegant example of how the world becomes different when the size of material shrinks to the scale of a single atom," Hone adds. "With what we're learning, we're eager to build useful devices for all kinds of applications."

    Ultimately, Zhong Lin Wang notes, the research could lead to complete atomic-thick nanosystems that are self-powered by harvesting mechanical energy from the environment. This study also reveals the piezotronic effect in two-dimensional materials for the first time, which greatly expands the application of layered materials for human-machine interfacing, robotics, MEMS, and active flexible electronics.
    http://www.techswarm.com/2014/10/res...-thinnest.html

    Quote This giant 3D printer can build houses from mud in the poorest regions
    A six-metre-tall 3D printer has been developed that can build cheap, sustainable houses using a clay-like paste.

    Created by Italian 3D printer company WASP, the giant, three-armed printer was demonstrated at Maker Faire Rome last week.

    While there are already 3D printers out there that can rapidly build houses, this model is unique as it can be assembled on site within two hours, and then filled with mud and fibre to construct extremely cheap dwellings in some of the most remote places on Earth.

    WASP CEO Massimo Moretti explained to Make:, the magazine that produces the faire, that this allows developers to work more closely with natural forms, rather than the square-shaped block homes that common brick dwellings are made from.

    The mud that goes inside the printer first needs to be mixed with another natural fibre, such as wool, to help bind it together, creating a grainy paste that can then be squeezed out into the desired shape, sort of as though you were icing a cake.

    Although they may not look like much, these homes can be up to three metres high, and when dry create a tough and sustainable shelter for people in rural or impoverished areas. Instead of traditional foundations, the ones created by the WASP printer at the Maker Faire Rome used cleverly designed layers of the mud mixture to make the walls strong.

    “While no plans are officially in place, Moretti states that the first WASP house may occur next year in Sardinia, due to the availability of wool, used as a fibrous binder in the printer’s mud, for the project,” writes Mike Sense for Make:.

    Check out the video of Moretti describing the printer and see it in action below:
    http://www.sciencealert.com.au/news/20141510-26336.html

    Quote Zap&Go portable charger fuels up in just 5 minutes

    An Oxford-based startup has turned to crowdfunding to help develop Zap&Go, a phone charger with an emphasis on speed and portability. Thanks to a graphene supercapacitor and an ad-hoc power supply, the device will reportedly charge to its 1,500-mAh capacity – enough to fully charge an iPhone 5s – in only five minutes and promises to be a much more practical solution than current alternatives, particularly when traveling.
    Our smartphones and tablets keep getting thinner, while displays keep getting more pixel-dense and power-hungry. As a consequence, the battery life of our portable devices rarely exceeds one day of heavy usage. In addition, the limitations of lithium-ion batteries mean that these devices can take hours to fully charge. For those who need more juice on the go, one solution is to use an external battery that can recharge our electronics when needed, even when we're miles away from a plug.

    Plenty of fast external batteries are already either on the market or on the horizon. Perhaps two of the most interesting projects currently in the works are the 2,600-mAh Petalite Flux and the Power Practical Pronto, which according to its inventors will also come in a 13,500-mAh version.

    But for all their capacity and convenience, these external batteries require bulky adapters that add to the clutter, making them unpractical to pack in your suitcase while you're traveling; and while they charge significantly faster than your typical smartphone, they still take 30 to 60 minutes to fully load up.

    By contrast, Zap&Go is designed specifically for speed and portability, as it can charge in just five minutes and doesn't require extra adapters, since the specially-developed power supply is embedded in the device itself. According to the product's Indiegogo campaign page, the device can charge any type of phone or tablet that comes with a standard 5-volt USB port.

    You can use the Zap&Go as a normal charger, plugging it into an electrical socket while your phone or tablet is charging normally and the device is completing its fast five-minute charge cycle; or, if you're pressed for time, you can just plug in the device for a quick and full charge-up, and only later, while you're on the go, connect the Zap&Go to your device and have it charge (either way, the phone or tablet itself will still charge at normal speed).

    The product, currently at a working prototype stage according to company founder Stephen Voller, required two major innovations: the first was to replace aluminum foils in supercapacitors with the much more conductive graphene, allowing the device to significantly shrink in size; the second was a new power supply to allow the charger to take in enough power in a limited amount of time.

    According to the product's Indiegogo campaign, the Zap&Go is set to be delivered in October 2015 for a pledge of US$99 and will ship with a US plug as standard, but will also include international plug adapters for the UK, Japan and the EU. At the time of writing, the Indiegogo campaign is one third of the way toward reaching its funding goal of $30,000, with 30 days still to go.

    The video below shows the Zap&Go in action.
    http://www.gizmag.com/zap-and-go-sup...charger/34228/
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  22. The Following 3 Users Say Thank You to TargeT For This Post:

    Cara (4th December 2015), Star Tsar (5th November 2014), Zampano (5th November 2014)

  23. Link to Post #92
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    This is pretty amazing, the first step to real 3d displays is finally here.

    Quote Pulse laser used to create 3D display in mid-air

    ou’ve probably seen projectors that can create images that seem to float in mid-air by painting light onto fog or water, but Japanese firm Aerial Burton has created something much more impressive. The recently demoed Aerial Burton display can create moving 3D images in mid-air using laser plasma technology.

    The Aerial Burton display isn’t currently capable of creating detailed images like you’d see on a screen projector, but it’s still a big leap when you consider there’s nothing up there off which to bounce light. That’s really the basis of most projection technologies — the light reflects off something to your eyes. The aerial display shown here uses lasers to ionize molecules in the air, so the source of the light is actually floating in mid-air where you see it.

    The images are produced by a 1kHz infrared pulse laser, which is directed into a 3D scanner. This apparatus reflects the pulses up into the air while focusing them on pre-defined points. By ionizing molecules in very localized areas, the device is essentially producing pockets of plasma that give off energy as photons. The flashes of light are short-lived, so the system has to constantly pulse new beams to keep the image alive.

    The next step is to increase the resolution of the images. Right now it can be a little hard to tell what each image is as it’s rotating around. This is more of a concern with busy backgrounds behind it. There are a few demos of this same technology in water, and the overall quality of the image is much higher. Air is obviously much less dense, so there may be fundamental limits to this kind of pulsed plasma laser tech.

    The designers believe the Aerial Burton display could be used in emergency situations to help people find evacuation routes and emergency supplies. It’s also portable and can be mounted in a car. You might not be able to render Princess Leia in full holographic detail, but a giant floating arrow that points to safety during an emergency seems doable.
    http://www.geek.com/science/pulse-la...d-air-1608487/
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  24. The Following 3 Users Say Thank You to TargeT For This Post:

    Cara (4th December 2015), Star Tsar (5th November 2014), Zampano (5th November 2014)

  25. Link to Post #93
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    I'm not sure if I'm excited about this or scared ****less.... click the source link for a good short video explaining pro/con's of the system... it costs 1$ to fire... 0_o

    Quote U.S. Navy Deploys Its First Laser Weapon in the Persian Gulf
    The U.S. Navy has deployed on a command ship in the Persian Gulf its first laser weapon capable of destroying a target.

    The amphibious transport ship USS Ponce has been patrolling with a prototype 30-kilowatt-class Laser Weapon System since late August, according to officials. The laser is mounted facing the bow, and can be fired in several modes -- from a dazzling warning flash to a destructive beam -- and can set a drone or small boat on fire.

    The Ponce “provides a unique platform” to deploy the new capability “in an operationally relevant region,” Vice Admiral John Miller, the 5th Fleet commander, said in an e-mailed statement. The ship is the 5th Fleet’s primary command and control afloat staging base for operations

    Since 2011, the Navy has boosted its presence in the Persian Gulf and the Strait of Hormuz, through which a fifth of the world’s traded oil flows. Equipped with naval mines and small vessels that practice swarming tactics to attack larger warships, Iranian officials have periodically threatened to close the waterway.

    The Navy laser wasn’t specifically designed or deployed to counter Iran’s arsenal of small armed vessels, Chief of Naval Operations Admiral Jonathan Greenert said in an interview earlier this year.

    “I wouldn’t target a country for a weapon, nor would I preclude putting together a weapons system for a country by itself,” he said.

    The laser deployment is “a worthwhile experiment” because “it’ll help us feel out the operational limitations” such as power constraints, Frank Kendall, the Pentagon’s top weapons buyer said at a Bloomberg Government breakfast in April.

    Testing the Weapon

    However, he said, “I still think we have some work to do on the technology side.”

    “What am I looking for? How does it operate in that environment -- heat, humidity, dust and at sea,” Greenert said in the interview. “It’s got to roll, move around, how much power does it take to sustain it?”

    “I have to take it out and get it wet, and the Arabian Gulf’s a pretty tough environment,” he said.

    Naval Sea Systems Command technicians developed the prototype over seven years at a cost of about $40 million. The Ponce crew was authorized to deploy the weapon after it passed a series of at-sea tests, including lasing static surface targets, the 5th Fleet spokesman Commander Kevin Stephens said in an e-mail statement.

    The prototype focuses the light from six solid-state commercial welding lasers on a single spot, according to a July 31 Congressional Research Service report. It “can effectively counter surface and airborne threats, to include small boats” and drones, Miller said, and firing it costs about a dollar a shot, according to the Navy.
    Adjustable Strength

    The device can emit progressively stronger beams, first to warn an adversary, and then destroy it if necessary, Chief of Naval Research Rear Admiral Matthew Klunder said at a Bloomberg Government session this year.

    The laser can be adjusted to fire a non-lethal dazzling flash at an incoming vessel so they know it’s there “all the way to lethal,” Klunder said. The laser’s range is classified.

    New York-based L-3 Communications Holdings LLC (LLL) and Pennsylvania State University’s Electro Optics Center have provided components and engineering support.

    The lessons from the one-year Ponce deployment will feed Navy laser development by industry teams led by BAE Systems Plc (BAESY), Northrop Grumman Corp. (NOC) and Raytheon Co. (RTN), to field a more powerful weapon, possibly by 2021.

    Those efforts are separate from military laser designators to guide precision munitions, non-lethal crowd control devices or discontinued instruments intended to blind enemy electro-optical sensors.
    http://www.bloomberg.com/news/2014-1...sian-gulf.html
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  26. The Following 2 Users Say Thank You to TargeT For This Post:

    Cara (4th December 2015), seko (1st February 2015)

  27. Link to Post #94
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Quote Controlling medication with your mind: Thought-regulation of genes made possible
    Scientists have created the first device which allows people to turn genes in mice on and off at will using only their brainwaves.

    In humans, the ability to regulate the expression of genes through thoughts alone could open up an entirely new avenue for medicine. A monitoring system that could pick up early neurological signs of an impending epileptic fit or a migraine, for example, could automatically trigger the manufacture and release of protein-based medication within the body.

    “Being able to control gene expression via the power of thought is a dream that we’ve been chasing for over a decade,” said Dr Martin Fussenegger from ETH Zurich, who led the research.

    The study made use of a human gene implanted in mice. A tiny chamber containing human cells and an LED light was inserted under each mouse’s skin. The genes had been genetically modified to be sensitive to light, which made it possible to trigger and manage their protein production through shining the near-infrared light from the LED on them.

    The human test subjects were divided into three groups, and asked to either meditate, play a game of Minecraft, or watch the light coming from the mouse’s body. Their brain activity was captured by a headset and analysed to establish their state of mind. The resulting signal was transmitted to the mice in the form of an electromagnetic field, which was able to light up the LED.

    The quantity of protein created by the guest genes depended on whether the human wearing the headset was relaxing or concentrating on playing Minecraft.

    Those who were asked to keep their eye on the mouse were able to see the effect their brain activity had on the red-coloured light, and thus on the genes within the implant. After some practice, this group learnt to exert conscious control over the amount of protein produced. They were able to alter their state of mind in order to change the output of the genes; a finding which gives the researchers hope that similar techniques could be used to influence implants within a person's own body.

    Fussenegger believes that the type of protein-based pharmaceuticals that can be produced in this way match the natural workings of the body more closely than currently used drugs, and may overcome some of the limitations imposed by traditional medicine.
    http://www.independent.co.uk/news/sc...e-9854874.html
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  28. The Following User Says Thank You to TargeT For This Post:

    Cara (4th December 2015)

  29. Link to Post #95
    United States Avalon Member thepainterdoug's Avatar
    Join Date
    27th November 2013
    Age
    70
    Posts
    3,225
    Thanks
    11,030
    Thanked 33,238 times in 3,168 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    our tech getting smaller, faster , smarter as our collective species gets fatter, slower and dumber . we are living in the dark ages with the lights on.

  30. The Following User Says Thank You to thepainterdoug For This Post:

    TargeT (16th November 2014)

  31. Link to Post #96
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Quote Posted by thepainterdoug (here)
    our tech getting smaller, faster , smarter as our collective species gets fatter, slower and dumber . we are living in the dark ages with the lights on.
    it almost seems like a natural trend to transhumanism when you look at it that way.

    However I do not agree, I think there are some who are "fatter, slower and dumber" but over all average intelect has increased, obesity is an issue but not a pervasive one, and if anything we have humans that are "faster" now than ever.

    I see humanity improving greatly, but these improvements are far eclipsed by technology; which can be very dis-empowering when you compare the two.

    we are just now moving into the steep part of the exponential curve of technology development; it's going to get REALLY interesting in the next few years.



    this gives you a hint at what I"m talking about (from a metadata standpoint)
    http://whathappensontheinternetin60seconds.com/
    Last edited by TargeT; 16th November 2014 at 18:45.
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  32. The Following 2 Users Say Thank You to TargeT For This Post:

    Amenjo (16th November 2014), Cara (4th December 2015)

  33. Link to Post #97
    United States Avalon Member thepainterdoug's Avatar
    Join Date
    27th November 2013
    Age
    70
    Posts
    3,225
    Thanks
    11,030
    Thanked 33,238 times in 3,168 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    target/ some amazing advancements for sure. my comment and your response could be debated for some time regarding their respective truths. both are correct to differing degrees.
    i just spoke at a college in my area and was again amazed on how strangely unfit and un healthy the class room looked, gobbling fast food and soda and only a few fitting within their weight class . and this was not an unusual case as i have seen it all over. added to this a certain lack of people skills etc.
    i am concerned we cannot digest the exponential acceleration of our tech. when i was a kid, i didn't have to digest the idea that my phone was changing every 6 months. it was one of many things i could take for granted as being there while was going thru all other adolescent changes.
    today its all in flux all the time. are we up to it?
    perhaps the people here at avalon are but not the general public who watch standard tv programs and msm as a daily diet. well , i guess it will go where its going to go regardless of my thoughts etc! thanks for the great post!

  34. The Following User Says Thank You to thepainterdoug For This Post:

    TargeT (17th November 2014)

  35. Link to Post #98
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    One of my favorite topics: energy storage! this one is a bit further out than 2 years however...
    Quote
    Tiny Batteries Could Revolutionize Green Energy
    Nanotechnology could dramatically improve energy storage for electronics, cars, and buildings.

    Nanosize batteries that are 80,000 times thinner than a human hair represent a promising new front. They could advance the use of electric vehicles, now limited by short driving ranges, and of renewable energy, which needs storage for times when the wind doesn't blow or the sun doesn't shine.

    The latest breakthrough: a "nanopore" that's the ultimate in miniaturization. It's a hole in a ceramic sheet, no thicker than a grain of salt, that contains all the components a battery needs to produce electric current. One billion of these holes, connected in a honeycomb fashion, could fit on a postage stamp.

    The itty-bitty battery delivers. It fully charges in 12 minutes and recharges thousands of times, according to University of Maryland researchers, who published their findings last week in the peer-reviewed journal Nature Nanotechnology.

    "We were blown away by the performance," says co-author Eleanor Gillette, a doctoral candidate in chemistry. She attributes its quick charging to the short distances needed to carry the electric current. She says the nanosizing could enable manufacturers to squeeze many batteries into a tight space.

    "It looks like a major advance," says George Crabtree, director of Argonne National Laboratory's Joint Center for Energy Storage Research. He says nanopores offer multiple advantages. Because they're identical, researchers-once they identify the optimal size-will be guaranteed consistent results that will make grid-scale use more promising, he says.

    Crabtree says this battery, like other recent advances in nanotechnology, would not have been possible even a decade ago. Though the field has been evolving for the past 15 years, it wasn't applied to energy storage until more recently. He says it could open the door to the transformative change that's needed in the battery world.


    Push for Better Batteries Expands

    The stakes are immense. Electric vehicles and renewable energy, hailed as climate change solutions, need cheaper and better batteries to achieve widespread use. For utilities to rely on intermittent power sources such wind or solar for a large share of their electricity, they will need back-up energy storage. (Related: "Seven Ingredients for Better Car Batteries")

    So the race is on-at universities, start-ups, and major companies like GE, IBM, and Toyota-to build a battery that goes beyond the incremental changes that have improved the performance of the lithium-ion battery, the industry standard-bearer developed in the 1970s and brought to market 20 years later.

    Researchers, some with funding from the U.S. Department of Energy, are working to develop or improve several types of batteries, which produce electricity by creating chemical reactions. Most batteries have three basic parts: the electrolyte to provide electrons, the anode to discharge them, and the cathode to receive them.

    By nanosizing materials and structures, scientists are trying to identify the optimal combinations at the molecular level.

    Last year, for example, University of Southern California researchers developed a new lithium-ion battery that uses porous silicon nanoparticles rather than traditional graphite anodes. The team, led by Chongwu Zhou, says the battery holds three times as much energy as comparable graphite-based designs and recharges within ten minutes.

    "The way to get high power is to nanosize it," says Gary Rubloff, an engineering professor who directs the University of Maryland's NanoCenter. "The world of nanoscaled batteries opens up a lot of different alternatives for how to manufacture them."

    Challenges Loom in Bringing Ideas to Market

    Commercializing the research won't be easy or quick. Many of the materials or assemblies in nanoscale batteries are currently too expensive for use beyond niche applications.

    "Developing such batteries will be a significant challenge for the field, and questions remain," write Paul Braun and Ralph Nuzzo of the University of Illinois at Urbana-Champaign in a commentary that accompanies the University of Maryland study and applauds its results.

    Also, low oil and natural gas prices have dampened demand for renewable energy sources such as wind and solar, which require grid-scale backup batteries.

    "It's hard to compete with oil and gas right now. Part of the problem is economics," says James Tour, professor of materials science and nanoengineering at Rice University in Houston, Texas. His team of researchers created a material consisting of forests of carbon nanotubes grown on sheets of graphene that could dramatically improve energy storage.

    Two companies, Texas-based Xidex and Israel-based Graphite Corporation, are developing a battery based on the Rice technology that could fully charge a smartphone in a few minutes. "It might be on the market in three years," Tour says.

    Stanford University professor Yi Cui says it could take three to five years to commercialize a new type of battery built by his team, which includes former U.S. Energy Secretary Steven Chu. Their battery, touted as a "pure lithium," uses lithium not only in the electrolyte but also in the anode, which is commonly graphite or silicon.

    Cui's lab found a solution to a common problem: Lithium, when put in the anode, can expand more than other materials during charging and even eat up the electrolyte. To prevent this, it built "nanospheres," a honeycomb-like microscopic layer that creates a flexible nonreactive film to shield the lithium.

    The team's battery, Chu said in an announcement in July, holds the potential to triple a cell phone's battery life and give electric vehicles a 300-mile driving range.

    Cui has experience commercializing his research. He founded Amprius, a Silicon Valley start-up whose board members includes Chu, to sell a new type of long-lasting lithium-ion battery.

    While it took two decades to bring the initial lithium-ion battery to the market, Crabtree says the current focus on energy storage-combined with the benefits of nanoscience-may expedite that process to between five and 10 years.

    "It's really a moment of opportunity right now," he says. "There's an opportunity to accelerate the pace of innovation."
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  36. The Following User Says Thank You to TargeT For This Post:

    Cara (4th December 2015)

  37. Link to Post #99
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    This is a very clever and awesome discovery:
    Quote Jackie Chan Blu-ray disc boosts solar panel efficiency by a massive 22%

    This one’s a bit crazy, but stick with me. Blu-ray discs, like CDs and DVDs before them, consist of a thin layer — or layers — of recording medium sandwiched between two bits of plastic. Data is stored on this medium in a series of pits — small indentations — that are about 75nm long. To read the data, a laser is bounced off the recording medium — where the medium is smooth and untouched (usually referred to as islands), the laser light bounces straight back into a sensor; where the pits are, the laser is reflected differently. Thus, binary data can be stored and read.

    n the case of Blu-ray, the binary data isn’t just burnt directly to the disc — compression is applied, and error control codes are added so that data can be recovered in the case of light scratches. Because the error control codes are applied every few bytes, the end result is a disc covered in quasi-random pits and islands that have a recurring pattern every 150 to 525 nanometers. (The iridescence — rainbow effect — of optical discs is caused by this repeating pattern, in case you wondered.)
    As it turns out, these two characteristics — a quasi-random pattern, repeating every 150 to 525nm — are almost perfectly tuned for trapping photons in the visible light and near-infrared spectrum. One of the main reasons that current solar cells aren’t that efficient is because many photons simply reflect off the panel, rather than being converted into electrons. You can probably see where this is going.






    To increase the efficiency of a solar panel by 22%, the researchers at Northwestern bought a copy of Police Story 3: Supercop on Blu-ray; removed the top plastic layer, exposing the recording medium beneath; cast a mold of the quasi-random pattern; and then used the mold to create a photovoltaic cell with the same pattern. As you can see in the image above, this process actually makes the nanopatterned solar cell have the same iridescence as a Blu-ray disc. [Research paper: doi:10.1038/ncomms6517]

    The end result is a solar panel that has a quantum efficiency of around 40% — up about 22% from the non-patterned solar panel. As you can see in the graph above, the nanopatterning increases the solar panel’s absorption and efficiency across the entire range of 400-700nm wavelengths (visible to near infrared).

    Moving forward, can we expect the price of mediocre Jackie Chan movies to soar? Probably not. Any Blu-ray disc should work — and anyway, the more important takeaway here is that we should start nanopatterning our solar panels immediately. It just so happens that taking a mold of a Blu-ray disc is a cheap and easy way to get your hands on a good quasi-random nanopattern — but in the future, the patterning could be produced directly, without the Blu-ray intermediate.
    http://www.extremetech.com/extreme/1...y-a-massive-22

    I wonder how long this will take to come to market
    Last edited by TargeT; 26th November 2014 at 18:24.
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  38. The Following User Says Thank You to TargeT For This Post:

    Cara (4th December 2015)

  39. Link to Post #100
    United States On Sabbatical
    Join Date
    30th June 2011
    Location
    The Seat of Corruption
    Age
    44
    Posts
    9,177
    Thanks
    25,610
    Thanked 53,662 times in 8,694 posts

    Default Re: Technological advances that will directly affect you in the next 2 years

    Silicone Based Moores Law, does it need to be re-written for a Diamond based technology exponential increase in speed/power?

    Quote Diamond can replace silicon for computer chips for faster, lighter and simpler devices
    Diamond can run 5 times hotter than Silicon without degrading in performance and is more easily cooled (with 22 times the heat transfer efficiency of silicon), can tolerate higher voltages before breaking down, and electrons (and electron-holes) can move faster through them. Already, semiconductor devices with diamond material are available that deliver one million times more electrical current than silicon or previous attempts using diamond.

    Diamond-based semiconductors are capable of increasing power density as well as create faster, lighter, and simpler devices.

    Akhan Semi, in collaboration with Argonne National Laboratory, has developed a series of advancements that allows us to manufacture standalone diamond materials, deposit diamond directly on processed silicon, fabricate complete diamond semiconductor devices, as well as attach diamond material to other electronics materials.

    Diamond wafer technology is producing thinner and cheaper devices already in use in information technology, the military and aerospace applications. In addition, diamond semiconductor will have a major impact on the consumer electronics, telecommunications and health industries, among many others, starting as early as 2015.

    Thin diamond film materials are able to alter the electronic properties and form device structures that are over a thousand times thinner than the leading silicon counterpart in addition to the previous state-of-the-art in diamond but with also increased performance, allowing the trend of smaller, faster, and more functional to continue.

    The Miraj Diamond™ platform resulted from the marriage of two scientific breakthroughs: the ability to deposit nanocrystalline diamond films at relatively low temperatures and a doping process that makes NCD into a good semiconducting materia

    Akhan Technologies are described at their website

    Practical Bipolar devices fabricated for the first time on Low cost Nanocrystalline Diamond (NCD) and polycrystalline diamond (Diamond-on-Silicon and Diamond-on-Insulator) wafers. Increased processing efficiency has rendered ultra-smooth, high yield, high uniformity film-quality.High precision (small feature size) architecture, allowing submicron (nm) control and microelectronic device fabrication, coupled with unrivaled material characteristics, allow for diamond to dramatically impact the global semiconductor market with:

    -Faster devices (no degraded performance under high heat or high power drive conditions with ultra-high electron mobility)
    * Lower material cost (30x to 1000x thinner material required to accomplish the same device function)
    * Lower system level cost (no added heat sinking needed, slower system temperature rise, less cooling equipment required)
    * Unbridled efficiency (highest power handling capability, power switching capability, switching speed, lowest On-state resistance, and ultimate high frequency capability)
    * Extreme Environment Capability (High Heat, High Power, High Pressure, Nuclear, Biological, Chemical, etc.)
    * Superior Scalability (nm to mm device feature size capability on 100, 200, and 300 mm commercial wafers)

    SOURCE - Wired, Akhan Semiconductor
    http://nextbigfuture.com/2015/01/dia...licon-for.html
    Hard times create strong men, Strong men create good times, Good times create weak men, Weak men create hard times.
    Where are you?

  40. The Following 2 Users Say Thank You to TargeT For This Post:

    Cara (4th December 2015), JRS (30th January 2015)

+ Reply to Thread
Page 5 of 13 FirstFirst 1 5 13 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts